自上料攪拌機經常行駛在建筑工地上，在發動機的使用過程中，避免不了各種油液的蒸汽生成的油泥，這些油泥和灰塵污垢混雜在一起受熱，成為汽車自燃的隱患之一，其次是大量灰塵與濕空氣結合后呈泥狀附著在發動機的零件與管路上，這會加快零件的老化與損壞；較臟的發動機艙容易成為老鼠及一些爬行動物的窩，所以發動機艙的清洗勢在必行。發動機艙該怎么清洗呢？自上料攪拌機教您怎么清洗發動機艙。

The automatic charging mixer often runs on the construction site. During the use of the engine, it is unavoidable to avoid the sludge generated by the steam of various oil. These sludge and dust are mixed together and heated, which becomes one of the hidden dangers of auto ignition. The second is that a large amount of dust and wet air are attached to the engine parts and pipelines in the form of mud, which will accelerate the aging of parts The dirty engine compartment is easy to become the nest of mice and some reptiles, so it is imperative to clean the engine compartment. How to clean the engine compartment? The self loading mixer teaches you how to clean the engine compartment.

1. 準備清洗工具，發動機外表清洗劑和發動機線束護理劑；一把小刷子，刷頭寬度不要太大，因?yàn)榘l(fā)動機艙的縫隙多且狹窄，用窄頭更加方便；一個口罩和一雙手套，發動機外表清洗劑對人體有一定的危害，味兒有點刺鼻，所以要準備口罩和手套。

1. Prepare cleaning tools, engine surface cleaning agent and engine harness care agent; a small brush, the width of the brush head should not be too large, because there are many and narrow gaps in the engine compartment, it is more convenient to use the narrow head; a mask and a pair of gloves, the engine surface cleaning agent has certain harm to the human body, the smell is a little pungent, so prepare masks and gloves.

2. 找一個停車的位置，發動機的清洗避免不了有污水流到地上，所以在準備清洗之前，盡量將車輛停放到人車之處。

2. Find a parking place, the engine cleaning can not avoid the sewage flowing to the ground, so before preparing for cleaning, park the vehicle to the place where there are few people and vehicles.
                 

3. 先將發動機的裝飾蓋卸掉，先用抹布或者刷子對發動機艙進行簡單的除塵，然后就可以用發動機外表清洗劑操作。將發動機內部的保險盒、點火線圈、發電機等一些不能沾水和清洗劑的零部件做一下防水處理（這些零部件可以單獨清潔），之后將清洗劑搖勻，再噴在發動機艙內的零部件上，注意噴灑距離保持在15厘米左右就可以了，盡量噴灑均勻一些，油泥多的地方適當多噴一些。

3. First remove the decorative cover of the engine, and then clean the engine compartment with a cloth or brush, and then use the cleaning agent on the surface of the engine. First, waterproof the fuse box, ignition coil, generator and other parts that can not be stained with water and cleaning agent (these parts can be cleaned separately). Then, shake up the cleaning agent and spray it on the parts in the engine compartment. Pay attention to the spraying distance of about 15 cm. Spray evenly as far as possible, and the place with more sludge is appropriate Spray more.

4. 用小刷子清理，在噴完清洗劑后，需等待5分鐘左右，讓清洗劑繼續化解油泥，直完全化解，然后用小刷子進行刷洗，可以明顯看到油泥化開的效果。發動機艙縫隙較多，一定要耐心刷干凈，因?yàn)橹筮€會噴上養護劑（相當于上了一層蠟油），如果不刷洗干凈，臟東西就封在里面了。自動上料攪拌機發動機的進氣管很容易沾上油泥，顏色難看且不易清洗，需要細心的刷干凈，還有一些走電、走油液的管路，也要清洗干凈，防止油泥和其它污物對它們進行腐蝕，造成泄漏。

4. Clean with a small brush. After spraying the cleaning agent, it is necessary to wait for about 5 minutes to let the cleaning agent continue to dissolve the sludge until it is completely dissolved, and then use a small brush to brush, which can obviously see the effect of the sludge. There are many gaps in the engine compartment, so you must brush it patiently, because after that, you will spray the curing agent (equivalent to a layer of wax oil). If you don't brush it clean, the dirty things will be sealed inside. The air inlet pipe of the automatic feeding mixer engine is easy to be stained with oil sludge. The color is ugly and not easy to clean. It needs to be cleaned carefully. Some power and oil pipelines also need to be cleaned to prevent oil sludge and other dirt from corroding them and causing leakage.

5. 清水清洗，清洗劑在化解油泥后，還是會附著在發動機艙內的各個零件上，所以在它們即將風干之前，需要用清水清洗干凈，切忌用高壓水槍清洗。在清洗之前先要做一下防范措施，就是先啟動發動機保持怠速狀態，這樣做的原因有兩點：一是防止點線圈等關鍵部位濺到水后，造成短時間啟動困難，二是發動機運轉后，機體溫度會上升，可以加速水蒸發變干。

5. Clean with water. After dissolving the sludge, the cleaning agent will still adhere to all parts in the engine compartment. Therefore, before they are about to dry, they need to be cleaned with clean water. Do not use high-pressure water gun to clean them. Before cleaning, the preventive measures should be taken, that is, start the engine to keep idle. There are two reasons for doing so: first, prevent the key parts such as the point coil from splashing with water, which makes it difficult to start in a short time; second, after the engine is running, the body temperature will rise, which can accelerate the evaporation and drying of water.

6. 線束護理劑，在用水清洗之后，一定要將發動機內部件上的水吹干，氣槍吹干是很好的方式，如果沒有，只能用吸水性好的毛巾擦干，然后待其完全晾干。然后將線束護理劑均勻地噴灑在發動機艙內的各個部件上就好了。這樣做可以防止油泥積累，減緩線束老化，減少老舊車型自燃的幾率。自上料攪拌機價格不算便宜，一定要保養好，讓它為您帶來更多的經濟收益。

6. After cleaning the harness with water, the water on the internal parts of the engine must be dried. Air gun drying is a good way. If not, only use a towel with good water absorption, and then let it dry completely. Then spray the harness care agent evenly on all parts in the engine compartment. This can prevent the accumulation of sludge, slow down the aging of wiring harness and reduce the risk of spontaneous combustion of old vehicles. The price of self feeding mixer is not cheap, so it must be well maintained to bring you more economic benefits.

以上就是如何清理自動上料攪拌機發動機艙油泥精彩內容的介紹，希望對大家有所幫助，如果您有選購攪拌機這方面的需求歡迎在我們的網站上進行留言。

The above is how to clean up the sludge in the engine compartment of the automatic feeding mixer. I hope it will help you. If you have the need to purchase the mixer, please leave a message on our website.