我們都知道，自上料攪拌機配置可以按照工地路況施工環境定制，隧道一般路況比較差，配置大動力發動機高強度后橋，可以降低礦用攪拌機的故障率，提高工作效率。受到了廣大用戶的追捧，攪拌機能適應很多的施工環境，轉速更穩定。下面為大家介紹一下引發自上料攪拌機突然熄火的原因排查方法。希望對大家有所幫助。

As we all know, the self loading mixer configuration can be customized according to the construction environment of the site road conditions. The tunnel road conditions are generally poor. The configuration of high-power engine and high-strength rear axle can reduce the failure rate of the mine mixer and improve the work efficiency. By the majority of users sought after, mixer can adapt to a lot of construction environment, more stable speed. The following is to introduce the cause of sudden flameout of self feeding mixer and the troubleshooting method. Hope to help you.

自上料攪拌機廣泛應用于修路、修橋、修隧道、農村基礎建設以及各大工程之中。在使用中會遇到各種故障性問題，下面就為大家簡單介紹一下引發自上料攪拌機突然熄火的原因排查方法。

Self feeding mixer is widely used in road, bridge, tunnel, rural infrastructure and other major projects. In use will encounter a variety of fault problems, the following is a brief introduction to the cause of sudden flameout from the feeding mixer troubleshooting method.

確定自上料攪拌機油路暢通，柴油機供給系統沒有空氣后，可拆開油泵蓋板，板動操縱手柄，撥動油泵拉桿，看拉桿是否靈活和柱塞彈簧是否斷裂。在自上料攪拌機拉桿靈活和柱塞彈簧沒斷的情況下，可啟動柴油機中速運轉10分鐘，還有斷火現象時，可用一只銅榔頭輕輕敲擊輸油泵大螺帽，一邊敲一邊聽柴油機聲音，如果聲音不正常，說明輸油泵活塞和推桿發卡，進行修理或更換。

After confirming that the oil path of the self feeding mixer is smooth and there is no air in the diesel engine supply system, remove the cover plate of the oil pump, move the control handle and pull the rod of the oil pump to see whether the rod is flexible and whether the plunger spring is broken. Under the condition that the pull rod of the self feeding mixer is flexible and the plunger spring is not broken, the diesel engine can be started to run at medium speed for 10 minutes. If the fire is still broken, a copper hammer can be used to tap the big nut of the fuel transfer pump gently and listen to the sound of the diesel engine at the same time. If the sound is abnormal, it means that the piston and push rod of the fuel transfer pump are jammed and repaired or replaced.
         

拆下自上料攪拌機噴油器總成，轉動曲軸數圈，即有水噴出，說明缸蓋，缸體有裂紋或砂眼，遇到這種情況時，可向用戶解釋或向自上料攪拌機公司反映。低壓油流暢通后，可用手壓泵排除油路中的空氣，打開泵頭放氣螺釘，直到?jīng)]有氣泡時，方可上緊放氣螺釘。

Remove the fuel injector assembly of the self feeding mixer, rotate the crankshaft for several turns, that is, water is ejected, which indicates that there are cracks or sand holes in the cylinder head and cylinder body. In case of this situation, you can explain it to the user or report it to the self feeding mixer company. After the low-pressure oil flow is smooth, the air in the oil circuit can be removed by hand pressure pump, and the pump head vent screw can be opened until there are no bubbles, then the vent screw can be tightened.

油嘴不霧化，油泵柱塞彈簧和彈簧座斷裂，卡死不工作，或是柴油內有水。拆下油嘴總成檢查開啟壓力和霧化，如果油嘴總成正常，可讓用戶用干凈柴油裝入壺中用油路旁接法進行試驗。打開自上料攪拌機油箱開關，拆下輸油泵進油管，看油流情況，如果油流很快，說明正常，如果油流時斷時續查油路。

The nozzle does not atomize, the plunger spring and spring seat of the oil pump are broken, stuck and does not work, or there is water in the diesel oil. Remove the nozzle assembly to check the opening pressure and atomization. If the nozzle assembly is normal, the user can load clean diesel into the pot and conduct the test by using the oil bypass method. Turn on the oil tank switch of the self feeding mixer, remove the oil inlet pipe of the oil pump, and check the oil flow. If the oil flow is fast, it means it is normal. If the oil flow is intermittent, check the oil circuit.

感謝您的閱讀，希望以上內容對您有所幫助，如您想了解更多精彩內容請點擊我們的官網：自動上料攪拌機http://www.wishnailspa.com。

Thank you for reading, hope the above content is helpful to you, if you want to know more wonderful content, please click our official website: automatic feeding mixer http://www.wishnailspa.com .