小型混凝土攪拌機汽缸是與活塞構成工作容積的部件，氣缸的作用是將壓縮空氣的壓力能轉換為機械能，驅動機構作直線往復運動、擺動和旋轉運動。那么，如何預防小型混凝土攪拌機汽缸破裂呢？下面為大家介紹下：

The cylinder of small concrete mixer is a component of working volume with piston. The function of cylinder is to convert the pressure energy of compressed air into mechanical energy, and drive the mechanism to make linear reciprocating motion, swing and rotary motion. So, how to prevent small concrete mixer cylinder rupture? Here is an introduction:

導致小型混凝土攪拌機氣缸破裂的因素很多，要預防氣缸破裂，應該做到：發動機溫度過高時，須等發動機溫度降低后，再加水發動；不得先啟動發動機，后加冷卻水，以免使氣缸崩裂；在嚴寒條件下車，須放凈冷卻水，啟動車時加熱水啟動；冬季停車若時間較長，又不能放水時，可間歇發動車輛，保持發動機有一定溫度而不致于結冰，不得用噴燈或明火直接烤車，同時使用的冷卻水要潔凈。
            

There are many factors leading to the small concrete mixer cylinder rupture. To prevent the cylinder rupture, we should do: when the engine temperature is too high, we must wait for the engine temperature to reduce, and then add water to start; Do not start the engine first, and then add cooling water, so as not to crack the cylinder; When getting off the vehicle in severe cold conditions, the cooling water must be discharged completely, and the heating water must be used to start the vehicle; In winter, if the parking time is long and the water can not be discharged, the vehicle can be started intermittently to keep the engine at a certain temperature without freezing. It is not allowed to use blowtorch or open fire to bake the car directly. At the same time, the cooling water used should be clean.

小型混凝土攪拌機如果氣缸套出現破損，發動機在進氣行程時會吸入冷卻液，而在壓縮行程和做功行程時高壓氣體又會從破損處進入冷卻水道。無論出現哪一種情況，都將妨礙可燃混合氣的形成和燃燒，甚使發動機不正常工作，將嚴重影響發動機的使用壽命。

If the cylinder liner of small concrete mixer is damaged, the engine will inhale coolant during the intake stroke, and the high-pressure gas will enter the cooling channel from the damaged place during the compression stroke and power stroke. No matter what happens, it will hinder the formation and combustion of combustible mixture, and even make the engine not work normally, which will seriously affect the service life of the engine.