自動上料攪拌機油封磨損如何？
來源：http://www.wishnailspa.com/日期：2021-05-19
概述：如果長時間使用，油封會磨損。If used for a long time, the oil seal will be worn 方案：只需更換新的油封即可。Solution
如果長時間使用，油封會磨損。
If used for a long time, the oil seal will be worn.
方案：只需更換新的油封即可。
Solution: just replace the new oil seal.
如果長時間不更換機油，則濾芯的質量會下降，機油會變得太臟，并且油封的磨損會更快。
If the oil is not changed for a long time, the quality of the filter element will decline, the oil will become too dirty, and the oil seal will wear faster.
方案：盡快更換液壓油和濾芯。
Solution: change the hydraulic oil and filter element as soon as possible.
驅動軸失衡并劇烈振動因此，主軸擺動油封磨損。方案：及時固定并更換軸。
The drive shaft is out of balance and vibrates violently. Therefore, the spindle swing oil seal is worn. Solution: fix and replace the shaft in time.
液壓油會變質和乳化，降低潤滑性能并加速油封的磨損。方案：盡快更換液壓油和濾芯。在嚴重的情況下，需要清潔系統。
Hydraulic oil will deteriorate and emulsify, reduce the lubrication performance and accelerate the wear of oil seal. Solution: change the hydraulic oil and filter element as soon as possible. In severe cases, the system needs to be cleaned.
泵支架松動，泵打開，泵固定螺栓松動，導致整個液壓泵振動并磨損油封。方案：始終檢查并全2方自上料攪拌機發生故障的可能性，以防止并避免發生故障。
The pump bracket is loose, the pump is opened, and the fixing bolts of the pump are loose, which leads to the vibration of the whole hydraulic pump and the wear of the oil seal. Solution: always check and eliminate the possibility of failure of all 2 self feeding mixers to prevent and avoid failure.
自上料攪拌機系統的回油不暢，回油管和散熱器堵塞，導致電動機殼體內的壓力升高，并且油封泄漏。方案：堵塞物并穩定回油回路。
The oil return from the feeding mixer system is not smooth, and the oil return pipe and radiator are blocked, resulting in the pressure rise in the motor housing and the oil seal leakage. Solution: remove the blockage and stabilize the oil return circuit.
如果散熱器不散熱，油的溫度將變得太高，粘度和潤滑性將降低，油封將過熱并且密封將無法工作。
If the radiator does not dissipate heat, the temperature of the oil will become too high, the viscosity and lubricity will be reduced, the oil seal will overheat and the seal will not work.
方案：散熱器上的障礙物并冷卻系統，以防止泵馬達磨損。在嚴重的情況下，有必要停止和停止發動機，并用水沖洗泵的電動機和散熱器殼體以達到冷卻效果。
Solution: remove the obstacles on the radiator and cool the system to prevent the pump motor from wearing. In severe cases, it is necessary to stop and stop the engine and flush the pump motor and radiator housing with water to achieve cooling effect.
在冬季運行期間，由于預熱不足，油溫過低，油封和油封無法達到理想的工作溫度。對策：啟動時停止油箱，以怠速運轉1020分鐘，并在機油溫度恢復正常時更換油箱。
During the winter operation, due to insufficient preheating and low oil temperature, the oil seal and oil seal can not reach the ideal working temperature. Countermeasures: stop the oil tank when starting, run at idle speed for 10 to 20 minutes, and replace the oil tank when the oil temperature returns to normal.
Thank you for reading, hope the above content is helpful to you, if you want to know more wonderful content, please click our official website: automatic feeding mixer manufacturer http://www.wishnailspa.com .
全國服務熱線
點擊撥打服務熱線：400-879-1999
