Mixing machine in the process of use sometimes there will be stuffy machine trip fault, so what is the reason? We first have to find out the cause, in order to better solve, and then to prevent the failure again next time.

　　分析：外力在膠帶寬度方向上的合力不為零或垂直于膠帶寬度方向的拉應力不均勻。由于導致膠帶跑偏的因素很多，所以需要從輸送機的設計、制造、安裝調試、使用維護等方面來膠帶跑偏，膠帶的兩側以及膠帶兩側的不同高度。同樣，如果在皮帶運行方向的垂直截面等處不安裝托輥支架等裝置，也會導致皮帶跑偏。

　　Analysis: the net force of external force on the width direction of the tape is not zero or the tensile stress perpendicular to the width direction of the tape is not uniform. Due to many factors that lead to the deviation of the belt, it is necessary to solve the deviation of the belt, the two sides of the belt and the different heights of the two sides of the belt from the aspects of conveyor design, manufacturing, installation, debugging, use and maintenance. Similarly, if the vertical section of the belt running direction is not installed, roller support and other devices will also lead to belt running deviation.

　　原因：投料過多，引起攪拌機負荷過大；攪拌系統葉片與襯板之間的間隙過大，攪拌過程中，增大了阻力；三角傳動皮帶太松，使傳動系統效率低；攪拌主機上蓋檢修開關被振松，引起停機。

　　Cause: too much feeding, resulting in excessive load of mixer; The gap between the blade and the lining plate of the stirring system is too large, which increases the resistance in the process of stirring. Triangle drive belt is too loose, so that the drive system efficiency is low; The safety maintenance switch on the upper cover of the stirring machine was vibrated loose, causing the machine to stop.

　　處理：檢查配料系統是否超標和是否有二次投料現象。檢查攪拌機葉片與襯板之間的間隙是否在3~8mm。檢查傳動系統三角皮帶的松緊程度并調整。檢查主機上蓋開關是否松動。

　　Treatment: check whether the batching system exceeds the standard and whether there is a second feeding phenomenon. Check whether the clearance between the mixer blade and the lining plate is 3~8mm. Check and adjust the tightness of the drive system triangle belt. Check whether the safety switch on the host cover is loose.

　　另外，在攪拌一體機的保養過程中，一定要積累一些的技能和保養方法。如果是自己不了的問題，還是需要找人員，這樣才能從根本上問題，順利完成維修。

　　In addition, in the maintenance process of the all-in-one mixing machine, we must accumulate some professional skills and maintenance methods. If you can't solve the problem yourself, you still need to find a professional, so as to fundamentally solve the problem and complete the maintenance smoothly.

　　在維修過程中，選用的維修材料一定要合適。如果材料出現問題，可能會導致后期使用過程中出現其他問題。這些問題的積累，對機器的影響是非常嚴重的。

　　In the maintenance process, the selection of maintenance materials must be appropriate. If there is a problem with the material, it may lead to other problems during later use. The accumulation of these problems, the impact on the machine is very serious.

　　更多詳細內容，點擊http://www.wishnailspa.com網站了解吧！

　　For more details, click http://www.wishnailspa.com!