我們在初次使用攪拌一體機的時候有哪些小知識需要大家了解呢？為了幫助用戶能夠詳細的了解產品知識，下面讓廠家來給大家簡單介紹一下。

What little knowledge do we need to know when we first use the all-in-one mixer? In order to help users understand the product knowledge in detail, let the manufacturer give you a brief introduction.

1、需仔細閱讀攪拌一體機說明書，檢查所帶配件是否齊全，如攪拌子，電源線等。

1. It is necessary to carefully read the manual of the all-in-one mixer and check whether the accessories are complete, such as mixer, power cord, etc.

2、攪拌一體機使用時，不可高速檔直接起動，應由低速逐步調高速，避免攪拌子不同步，引起跳動。

2. When the mixing machine is used, it is not allowed to start directly at high speed. It should be gradually adjusted from low speed to high speed, so as to prevent the agitator from being out of sync and causing jumping.

3、延長攪拌一體機使用壽命很好的方法中速運轉。

3. Medium speed operation is a good way to prolong the service life of the mixing machine.

4、攪拌一體機不使用后，需保持它的干燥清潔。

4. The all-in-one mixer shall be kept dry and clean after it is not used.

此外還應該知道攪拌設備使用不當出現的故障，比如：

In addition, you should know how to solve the problems caused by improper use of mixing equipment, such as:

在選擇攪拌容器時，應根據生產規模(即物料處理量)、攪拌操作目的和物料特性確定攪拌容器的形狀和尺寸，在確定攪拌容器的容積時應合理選擇裝料系數，盡量提高設備的利用率

When selecting the mixing container, the shape and size of the mixing container shall be determined according to the production scale (i.e. material handling capacity), mixing operation purpose and material characteristics. When determining the volume of the mixing container, the loading coefficient shall be reasonably selected to maximize the utilization of the equipment

溫度探頭正確接入，只拔掉重新插入溫度探頭就好，其次需確保溫度探頭在攪拌器正常運行前接入，使用期間不建議經常拔動測溫探頭

The temperature probe shall be correctly connected. Just unplug and re insert the temperature probe. Secondly, ensure that the temperature probe is connected before the normal operation of the mixer. It is not recommended to frequently unplug the temperature probe during use

噪音大主要是因為長期高速或超載使用，導致電機共鳴，只要在電動攪拌器要求范圍內使用即可

High noise is mainly caused by long-term high-speed or overload use, which causes resonance of the motor. It can be used within the requirements of the electric mixer

電源插頭松動，關機檢查電源插頭是否損壞，接入是否正常

The power plug is loose. Shut down the machine to check whether the power plug is damaged and whether the connection is normal

攪拌軸位置不當所致，稍微移動燒杯，攪拌軸中心線鉛錘

Due to improper position of the mixing shaft, move the beaker slightly to the center line of the mixing shaft with a plumb bob

加藥支架偏移，請水平45度角轉動加藥支架合理位置，并重新加藥即可

The dosing support is offset. Please rotate the dosing support at a horizontal angle of 45 degrees to a reasonable position and refill

程序設置疏漏，重新返回核對，并進行相應的攪拌軸設置

If the program setting is not correct, check again and set the mixing shaft accordingly

以上就是攪拌一體機廠家為大家分享的小知識，希望以上的內容能夠?qū)Υ蠹矣兴鶐椭?，后期會整理更多資訊給大家，敬請關注我們的網站www.wishnailspa.com更新。

The above is the little knowledge shared by all-in-one mixer manufacturers. I hope the above content can be helpful to you. More information will be sorted out later for you. Please pay attention to our website www.zkhntjbj Com update.