攪拌機主機工作時有響動是為什么？
來源：http://www.wishnailspa.com/日期：2021-04-22
概述：在攪拌機生產過程中，您或許遇到過攪拌機主機工作時有響動的情況，那么您知道這是什么原因造成的嗎？In the production process of bl
在攪拌機生產過程中，您或許遇到過攪拌機主機工作時有響動的情況，那么您知道這是什么原因造成的嗎？
In the production process of blender, you may have encountered the situation that the main engine of blender vibrates when it works. Do you know what causes this?
攪拌機主機在工作時有響動是為什么？
Why does the mixer host sound when it works?
1）檢查攪拌主機主軸承是否發熱，如果在運轉過程中發熱，檢查是不是沒有潤滑油了，軸承是否有損壞，保護圈有無摩擦。
1) Check whether the main bearing of the main mixer is hot. If it is hot during operation, check whether there is no lubricating oil, whether the bearing is damaged, and whether the protective ring has friction.
2）打開水泥攪拌機攪拌主機觀察門看看攪拌葉片是否有斷裂、如有斷裂、清理斷裂的葉片，更換新的。
2) Open the observation door of cement mixer to see if the mixing blade is broken. If so, clean the broken blade and replace it with a new one.
3）攪拌葉片是否與內襯板有碰撞，如有碰撞，調整葉片與襯板的間隙（小于5mm）。
3) Whether the mixing blade collides with the lining plate, if so, adjust the clearance between the blade and the lining plate (less than 5mm).
4）檢查骨料粒徑是不是超標（要不大于80mm），如果粒徑超標，應該按標準選配料。
4) Check whether the particle size of aggregate exceeds the standard (no more than 80mm). If the particle size exceeds the standard, the mixture should be selected according to the standard.
5）花鍵軸配合是否松動，如果配合松動，要更換華鍵軸或軸套，并調整同軸度。以上這五方面的原因就是導致攪拌機主機工作時有響動的主要因素，希望對大家有所幫助。
5) If the fit of spline shaft is loose, replace the key shaft or shaft sleeve, and adjust the coaxiality. The above five reasons are the main factors that cause the mixer host to ring when working. I hope it can help you.
那么，在攪拌機生產過程中如何避免這些現象的產生呢？
So, how to avoid these phenomena in the production process of mixer?
1.應經常檢查鋼絲繩磨損情況并在其表明涂少許潤滑油，鋼絲繩磨損到一定程度后，應進行更換。
1. The wear condition of steel wire rope should be checked frequently and a little lubricating oil should be applied on it. After the steel wire rope is worn to a certain extent, it should be replaced.
2.檢查減速箱油面，油泵油量，檢查各潤滑部位的情況，往料斗滾輪軸承及滑輪軸承加注潤滑油。
2. Check the oil level of the gearbox and the oil quantity of the oil pump, check the condition of each lubricating part, and add lubricating oil to the hopper roller bearing and pulley bearing.
3.檢查行程開關搖臂是否松動，如有松動應予必要調整。
3. Check whether the rocker arm of the travel switch is loose, and adjust it if necessary.
4.檢查葉片連接螺栓，支撐臂連接螺栓是否松動酌情調整，葉片與筒壁間的間隙大間隙5mm并作必要的擰緊。
4. Check whether the connecting bolts of blade and support arm are loose, adjust them as appropriate, and the clearance between blade and cylinder wall is 5mm, and tighten them as necessary.
5.檢查軸端密封，葉片，襯板等一算部位，作必要的調整修理和更換。
5. Check the shaft end seal, blade, liner and other parts, and make necessary adjustment, repair and replacement.
關于攪拌機主機工作時有響動的原因，以及平時使用過程如何預防的問題就介紹到這。
This is the reason why the mixer host works and how to prevent it during normal use.
全國服務熱線
點擊撥打服務熱線：400-879-1999
