1. If there is oil output from the hydraulic pump of the loading mixer truck, we can check whether it works normally in time. If it is not normal, it may be that some equipment accessories in the pressure oil circuit are stuck for other reasons and are at the place of oil return, resulting in short circuit of pressure oil circuit and overflow circuit, or loose pipe joints. When some equipment in the oil circuit leaks seriously, or the seals of hydraulic cylinder and hydraulic motor are damaged. The solution is to directly disassemble the relevant equipment for cleaning to see if the corresponding equipment is damaged. Replace it when it's time to replace it and check it when it's time to check.

2、看自上料攪拌車液壓泵是不是能輸出液壓油呢。如果說是新的液壓泵，沒有液壓油，可能是泵體有缺陷，讓吸油腔和壓油腔有相通的情況發生，失去壓油能力，應及時找魯樽機械廠家更換。若不是新的液壓泵，無液壓油輸出，則可能是泵的轉向不對，零件磨損嚴重或損壞，及時更換。

2. See if the hydraulic pump of the self loading mixer can output hydraulic oil. If it is a new hydraulic pump without hydraulic oil, it may be that the pump body is defective, so that the oil suction chamber and oil pressure chamber are connected. If the oil pressure capacity is lost, it should be replaced by Lu Zun machinery manufacturer in time. If it is not a new hydraulic pump and there is no hydraulic oil output, the steering of the pump may be wrong, and the parts may be seriously worn or damaged. Replace them in time.

3、混凝土攪拌車的液壓系統能建立正常壓力，一些管路或者液壓缸中間是沒有壓力的，可能就是因為管路、小孔或節流閥、換向閥這些部位堵住了。所以要仔細查看檢查壓力有沒有油液通過，找出原因，然后來排除。

3. The hydraulic system of the concrete mixer can establish normal pressure. There is no pressure in some pipelines or hydraulic cylinders. It may be because the pipelines, small holes, throttle valves and directional valves are blocked. Therefore, check carefully to see if there is oil passing through the pressure, find out the cause, and then eliminate it.

4、若混凝土攪拌車的液壓泵輸出流量隨壓力升高而顯著減小，且壓力達不到規定值，則是由于液壓泵磨損后間隙增大所致。排除方法是測定液壓泵的容積效率，就可以確定這個泵是不是能繼續使用的，對磨損嚴重的產品，一定進行修配或更換。

4. If the output flow of the hydraulic pump of the concrete mixer decreases significantly with the increase of the pressure, and the pressure does not reach the specified value, it is due to the increase of the clearance after the hydraulic pump is worn. The elimination method is to measure the volumetric efficiency of the hydraulic pump, so as to determine whether the pump can continue to be used. The severely worn products must be repaired or replaced.

以上就是今天給大家講解的詳細內容，更多的精彩內容請點擊我們的網站自動上料攪拌機http://www.wishnailspa.com ，我們會有更多的精彩內容等您查看.

The above is the detailed content explained to you today. For more wonderful content, please click our website automatic feeding mixer http://www.wishnailspa.com  , we will have more wonderful content for you to see