There are always some small problems in the long-term use of the full-automatic feeding machine. At this time, as an equipment manager, what should we do? Wait for the manufacturer to repair and delay the production. As the saying goes, it's better to ask others than yourself. Some simple small problems can be solved by yourself. The most common problem of the full-automatic feeder is that when the pneumatic pump is used as the vacuum source, the materials may not be sucked up. There are still many reasons for this, mainly in the following aspects.

可以先檢查控制系統有沒有問題，比如說全自動上料機的各個參數，吸料，放料的時間是準確無誤的，要是在這里有問題吸料機就有或許不能正常的吸料，應及時的進行更改處理。

You can first check whether there is a problem with the control system. For example, the parameters of the full-automatic feeding machine, the time of suction and discharge are accurate. If there is a problem here, the suction machine may not be able to suck normally and should be changed in time.

對設備的氣動泵進行檢查，看看它的壓縮空氣的管路的接口是否有配合。大部分情況下氣動泵的氣源壓力是在6到7mpa，要是管路連接正常，就應該檢查一下氣源的氣動泵。

Check the pneumatic pump of the equipment to see whether the interface of its compressed air pipeline is matched. In most cases, the air supply pressure of the pneumatic pump is 6 to 7MPa. If the pipeline connection is normal, you should check the pneumatic pump of the air supply.

吸料機不能正常的進行吸料也有或許是因?yàn)闄C(jī)器的拆裝移動，在上蓋和筒體卡箍出現漏氣的情況，從而導致正常進行吸料作業。

The suction machine can not suck the material normally, or it may be due to the air leakage in the upper cover and cylinder clamp due to the disassembly and movement of the machine, resulting in the normal suction operation.

全自動上料機

Automatic feeding machine

將上料機的上蓋代開，把過濾板拿出來往后調查在濾芯上面的灰塵雜質是不是太多了，或許有的灰塵已經結成了固體的凝塊，這種情況都會讓吸料機以不正常的壓力進行吸料，出現這種問題，只要用氣槍吹掃干凈就可以了。

The upper cover of the feeder is replaced, and the filter plate is taken out to investigate whether the dust impurities on the filter core are too much. Maybe some of the dust has already formed solid clot, which will cause the suction machine to absorb the material under abnormal pressure.

對全自動上料機的吸料管道進行檢查，是不是上面出現了漏氣，其他要注意地方就是所有的卡箍上面是不是都有密封圈且密閉圈無老化、無漏氣。在檢查的時分可以依據上面的順序來進行，假如發現某一段問題的把它換掉或許是清潔干凈就可以了，要是仍是找不到原因的話可以找相關的人員或者聯系廠家來進行檢查和維護。

Check whether there is air leakage on the suction pipe of the full-automatic feeding machine. Other points to pay attention to are whether there are sealing rings on all clamps, and the sealing rings are free of aging and air leakage. During the inspection, it can be carried out according to the above sequence. If you find a problem, replace it, perhaps clean it. If you still can't find the reason, you can find relevant professional personnel or contact the manufacturer for inspection and maintenance.