Mixer truck is a construction equipment used in construction. However, in the work, the phenomenon of concrete solidification in the mixer truck often occurs in the concrete mixer truck. Once this situation occurs, it will affect the normal operation of the concrete mixer truck to a great extent. What about this? This is a problem that many construction parties want to know.

指出：混凝土凝結在攪拌車罐里面的緣由有很多，除了沒有及時清洗外，其中主要的原因是攪拌車發動機不能運作，由于沒有動力輸入液壓機而招致液壓機中止工作，使得裝料罐不能轉動而讓混凝土凝結在攪拌車罐里面。那么怎么樣除掉凝固在攪拌車?yán)锩娴幕炷聊兀楷F(xiàn)在給大家介紹兩種方法：

Experts pointed out that there are many reasons for the concrete to coagulate in the mixer tank. In addition to not being cleaned in time, the main reason is that the mixer engine can not operate. Due to the lack of power input to the hydraulic press, the hydraulic press stops working, so that the loading tank can not rotate and the concrete can coagulate in the mixer tank. So how to get rid of the concrete solidified in the mixer truck? Now let's introduce two solutions:

方法一、電焊或氣割

Method 1: electric welding or gas cutting

混凝土凝固后，其主要成分是硅酸二鈣、硅酸三鈣。理論上講，鹽酸可以與之反應解除其固態形狀。由于攪拌車的料口很小，鹽酸量難以控制，且鹽酸也可以與攪拌車罐體發生反應，所以操作很難實現。實踐中一旦出現這種情況，往往需要用電焊或氣割切開罐體，然后將凝固的混凝土機械破碎。

After the concrete is solidified, its main components are dicalcium silicate and tricalcium silicate. Theoretically, hydrochloric acid can react with it to remove its solid shape. Because the material port of the mixer truck is very small, the amount of hydrochloric acid is difficult to control, and hydrochloric acid can also react with the tank of the mixer truck, so the operation is difficult to achieve. Once this happens in practice, it is often necessary to cut the tank body with electric welding or gas cutting, and then mechanically break the solidified concrete.

方法之二、風炮

Method 2: air cannon

如果攪拌車內的混凝土已經凝固，建議可以用“風炮”打碎已經凝結的混凝土，然后一點點鏟出來！通常罐體下部要割開一個口，然后加翻開一個原來就有用羅絲上緊的封蓋，這個蓋是讓有需求進去工作時翻開通風和緊急情況放料的。在打罐過程中人在罐里面要通風，在裝料罐入口應放臺風扇吹風進去，而“風炮”工作時會起灰塵，又要接上水管淋濕打碎的混凝土。把罐里面的混凝土打碎鏟出以后再把割開部分焊接上，上回封蓋，裝滿水試下轉動能否正常，然后少量裝料遞增看液壓機工作能否正常，如果一切正常則表示可以繼續運作了。

If the concrete in the mixer truck has solidified, it is recommended to break the solidified concrete with an "air cannon" and shovel it out a little bit! Usually, a hole should be cut in the lower part of the tank body, and then a cover that was originally tightened with rose should be opened. This cover is used to turn on the air and discharge materials in case of emergency. In the process of beating the tank, people should be ventilated in the tank. A fan should be placed at the inlet of the charging tank to blow in. When the "air cannon" works, it will dust, and a water pipe should be connected to wet the broken concrete. After the concrete in the tank is broken and shoveled out, weld the cut part, seal the cover, fill it with water, test whether the rotation is normal, and then add a small amount of material to see whether the hydraulic press works normally. If everything is normal, it means that it can continue to operate.

混凝土結塊或者凝固在罐體內，會對攪拌車造成很大的傷害，攪拌車的混凝土凝固了怎么處理？通過以上介紹，相信廣大用戶對這個問題已經有所了解。

Concrete caking or solidification in the tank will cause great damage to the mixer truck. How to deal with the concrete solidification of the mixer truck? Through the above introduction, I believe that the majority of users have understood this problem.