混凝土會在短時間內凝結成塊，并且會對自動上料攪拌機的鋼材部分跟油漆造成一定的腐蝕，所以每次使用攪拌機后要及時清洗，洗凈粘附在混凝土儲存罐和進出料口的混凝土是每日維護必須認真進行的工作。

　　The concrete will condense into blocks in a short time, and will cause certain corrosion to the steel parts and paint of the automatic feeding mixer. Therefore, it is necessary to clean the concrete adhered to the concrete storage tank and the inlet and outlet of the concrete after each use of the mixer.

　　其中包括：

　　These include:

　　1、每次攪拌機裝料前用水沖洗進料口，使進料口在裝料時保持濕潤；

　　1. Wash the feed inlet with water before each mixer loading to keep the inlet wet during loading;

　　2、在裝料的同時向隨車自帶的清洗用水水箱中注滿水；

　　2. At the same time of loading, fill the water tank with water;

　　3、裝料后沖洗進料口，洗凈進料口附近殘留的混凝土；

　　3. After loading, wash the inlet to clean the residual concrete near the inlet;

　　4、攪拌機在下次裝料前切記放掉混凝土貯罐內的污水；

　　4. Remember to discharge the sewage in the concrete tank before the next loading of mixer truck;

　　5、到工地卸料后，沖洗出料槽，然后向混凝土貯罐內加清洗用水30—40 L；在車輛回程時保持混凝土貯罐正向慢速轉動；

　　5. After unloading at the construction site, wash the discharge tank, and then add 30-40 l of cleaning water into the concrete storage tank; keep the concrete storage tank in forward and slow rotation when the vehicle returns;
             

　　6、每天收工時徹底清洗攪拌機混凝土貯罐及進出料口周圍，保證不粘有水泥及混凝土結塊。

　　6. At the end of each day, thoroughly clean the concrete storage tank of the mixer truck and the surrounding of the inlet and outlet to ensure that there is no cement and concrete caking.

　　以上這些工作只要一次不認真進行，就會給以后的工作帶來很大的麻煩。

　　As long as the above work is not carried out seriously, it will bring great trouble to the future work.

　　長時間使用攪拌機，不僅需要保養汽車零件配件等，對于攪拌機外表漆面的保養也是比較重要的。

　　Long time use of mixer, not only need to maintain auto parts and accessories, but also the maintenance of exterior paint surface of mixer is more important.

　　1、攪拌機在太陽紫外線的照射下，漆膜會不斷向空氣中蒸發油份來達到保護自身的作用，時間長了就會造成漆面油分的過分散失。漆面的亮度、深度都大打折扣，漆面會慢慢發白，形成氧化層，縮短了車漆的壽命。攪拌機漆面氧化嚴重的話可以通過研磨和拋光來處理。

　　1. Under the ultraviolet radiation of the sun, the paint film will continuously evaporate oil to the air to protect itself, which will cause excessive loss of the paint oil over time. The brightness and depth of the paint are greatly reduced, and the paint surface will slowly turn white and form an oxide layer, which shortens the service life of the car paint. If the paint surface of mixer is seriously oxidized, it can be treated by grinding and polishing.

　　2、如果平時不對攪拌機漆面作護理，金屬漆可能產生一種非常細微的裂痕，會不斷地滲透車漆，直到穿透整個色漆層，這種現象就叫“龜裂”。如果裂紋中有車蠟，會發現車身有條紋狀的龜裂現象。經常打蠟可以讓龜裂情況逐漸減少。

　　2. If you don't take care of the paint surface of the mixer truck at ordinary times, the metallic paint may produce a very subtle crack, which will continuously penetrate the paint until it penetrates the whole paint layer. This phenomenon is called "cracking". If there is car wax in the crack, the car body will be found to have striated cracking phenomenon. Regular waxing can reduce cracking.

　　3、攪拌機上出現面狀磨蝕。很可能是因為昆蟲、鳥糞、樹汁、焦油、瀝青引起的。一些輕微的蝕痕可以用研磨拋光來。

　　3. Surface abrasion occurred on the mixer. It is probably caused by insects, bird droppings, tree sap, tar and asphalt. Some minor etchings can be resolved by grinding and polishing.

　　以上就是對于攪拌機漆面保養方法，希望對你有所幫助！如您有其他業務疑問，歡迎咨詢我們的網站！

　　The above is for the mixer paint maintenance methods, hope to help you! If you have other business questions, welcome to consult our website!