The mixing shaft end of automatic feeding mixer series is a combined seal type, which is composed of multi-layer seals such as rubber seals and steel seals. The quality of sealing affects the overall performance of the whole mixing station. Therefore, it is very important to choose a good seal. The root cause of mixer shaft end leakage is the damage of floating seal. Due to the damage of seal and oil seal, the lubrication system is short of oil, which leads to the wear of sliding hub and rotating hub.

由于軸端泄漏和與攪拌軸摩擦引起的軸承磨損，軸端溫度過高。 主軸端是一個集中部分，在高強度應力作用下，零件的使用壽命將大大減少。 因此，軸端密封，油封，滑動輪轂和旋轉輪轂中的密封及時更換; 建議將主軸端部的泄漏端側的軸承作為原始密封配件，以避免尺寸差異，磨損和損壞大軸及時檢查潤滑系統：

The temperature of the shaft end is too high due to the leakage of the shaft end and the bearing wear caused by the friction with the stirring shaft. The spindle end is a concentrated part. Under the action of high strength stress, the service life of parts will be greatly reduced. Therefore, the shaft end seal, oil seal, seal in sliding hub and rotating hub should be replaced in time; it is suggested that the bearing on the leakage side of the spindle end should be used as the original sealing parts to avoid dimensional difference, wear and damage to the main shaft, and the lubrication system should be checked in time

1.潤滑系統主油泵旋轉軸磨損現象

1. The main oil pump rotating shaft of the lubrication system is worn

2.潤滑系統主油泵壓力表接口柱塞不能正常工作

2. The plunger at the pressure gauge interface of the main oil pump of the lubrication system cannot work normally

3.漸進式油分配器閥閥芯在潤滑系統中堵塞，無法分配。

3. The valve core of progressive oil distributor safety valve is blocked in the lubrication system and cannot be distributed.

由于上述原因，軸端潤滑系統出現故障，需要更換潤滑系統的主油泵。

As a result of the above reasons, the shaft end lubrication system fails and the main oil pump of the lubrication system needs to be replaced.
          

如果你想做一個自動上料攪拌機，你應該從以下幾個方面入手：

If you want to make an automatic feeding mixer, you should start from the following aspects:

1）整個自動上料攪拌機的成本控制。 這主要是指自動上料攪拌機，因為自動上料攪拌機的投入和生產成本相對較低且易于管理。

1) Cost control of the whole automatic feeding mixer. This mainly refers to the automatic feeding mixer, because the input and production costs of the automatic feeding mixer are relatively low and easy to manage.

2）細分整個攪拌機的生產過程，掌握每個細分生產過程的成本。

2) Subdivide the whole mixer production process, master the cost of each production process.

3）做好整個攪拌機的銷售計劃，制定相應的生產和銷售計劃。

3) Do a good job in the whole mixer sales plan, formulate the corresponding production and sales plan.

4）做好全站金融審計制度，確保整個資金鏈的有序發展。 建議是減少銷售，而不是缺乏資金鏈。

4) Do a good job in the whole station financial audit system to ensure the orderly development of the whole capital chain. The suggestion is to reduce sales, not lack of capital chain.

以上是自動上料攪拌機混合器軸端泄漏的原因介紹，相信大家都有所了解了，如想了解更多精彩資訊請點擊我們的網站：http://www.wishnailspa.com

The above is the reason for the leakage of the shaft end of the automatic feeding mixer. I believe you all know about it. For more wonderful information, please click our website: http://www.wishnailspa.com