自動上料攪拌機設備的4個維護要點
來源：http://www.wishnailspa.com/日期：2022-11-23
概述：要想設備的使用時間較長的話，按照規定時間進行設備保養、修理、維護，磨損配件的換新等較為重要。那么作為攪拌機在平時維護的時候要注意哪
要想設備的使用時間較長的話，按照規定時間進行設備保養、修理、維護，磨損配件的換新等較為重要。那么作為攪拌機在平時維護的時候要注意哪些方面呢？以下為您介紹4個方面，可以參考。
If you want to use the equipment for a long time, it is important to maintain, repair and maintain the equipment according to the specified time, and replace worn parts. What aspects should be paid attention to when maintaining the mixer? Here are four aspects for your reference.
1、 Automatic feeding mixer transmission system
1、攪拌機的傳動齒輪、減速箱、鏈條按規定加潤滑油；
1. Add lubricating oil to the drive gear, reducer and chain of the mixer as required;
2、傳動部分聲音正常，減速箱、軸承無發熱現象；
2. The sound of the transmission part is normal, and the reducer and bearing are free of heat;
3、三角輸送帶松緊適當；
3. The triangular conveyor belt is properly tightened;
4、鋼絲繩應沒有較大的磨損，夾頭與連接牢，表面涂油脂潤滑；
4. The steel wire rope shall be free from major wear, the chuck shall be firmly connected, and the surface shall be coated with grease for lubrication;
5、制動器和離合器性能較好好，剎車片磨損較大應該換新。
5. The brake and clutch have good performance, and the brake pads should be renewed due to heavy wear.
二、自動上料攪拌機其它潤滑部件
2、 Other lubricating parts of automatic feeding mixer
1、主機啟動或按規定時間給攪拌機軸端密封注油，以使油封結構長期正常工作；
1. Start the main engine or inject oil into the shaft end seal of the mixer at the specified time, so that the oil seal structure can work normally for a long time;
2、其它加油點，如旋轉、旋轉的車輪和履帶等，應按規定時間加油。
2. Other refueling points, such as rotating and rotating wheels and tracks, shall be refueled at the specified time.
三、自動上料攪拌機混合系統
3、 Automatic feeding mixer mixing system
1、檢查攪拌筒運轉是否穩定，襯板、葉片損壞要換新；
1. Check whether the mixing drum operates stably, and replace the damaged lining plates and blades;
2、按照規定時間清理卡在攪拌機內的混凝土；
2. Clean the concrete stuck in the mixer within the specified time;
四、自動上料攪拌機清理和緊固
4、 Cleaning and fastening of automatic feeding mixer
1、主機、支架、裝載支架等設施的安裝連接應牢；
1. The installation and connection of host, support, loading support and other facilities shall be firm;
2、混凝土攪拌機身、場地等的清潔；
2. Cleaning of concrete mixing machine body and site;
3、基礎周圍不應有積水，水路應在冰凍季節做好保溫措施；
3. There should be no ponding around the foundation, and thermal insulation measures should be taken for the waterway in freezing season;
The above are the maintenance points of the automatic feeding mixer equipment introduced to you. Have you done it? If your mixing plant needs to be replaced or has other problems, please pay attention to us http://www.wishnailspa.com 。
全國服務熱線
點擊撥打服務熱線：400-879-1999
