很多操作人員在工作期間會遇到過自動上料攪拌機不能行走的情況。如果不能正常行走，肯定會影響正常工作。但是，大家不要慌張，找原因，排除故障。下面就來簡單分析一番吧。

Many operators will encounter the situation that the automatic feeding mixer cannot walk during work. If you can't walk normally, it will certainly affect your normal work. However, don't panic, find the reason and eliminate the fault. Let's make a simple analysis.

檢查變速箱限油閥和變速箱壓力表。如果發現變速箱和變距油缺失，應加新油，但不能過多，否則會引起變速箱發熱。通常，將其添加到限制中油可以流出位置閥。

Check the transmission oil limit valve and the transmission pressure gauge. If the transmission and variable distance oil are found to be missing, add new oil, but not too much, otherwise the transmission will be heated. Usually, oil added to the limit valve can flow out of the position valve.

檢查臂架能否升降，是否有轉向。如果動臂可以升降，也可以完成轉向動作，但機器本身無法實現行走的過程。這主要是由于變速泵損壞導致缺油缺水造成的。

Check whether the boom can rise and fall and whether there is steering. If the boom can rise and fall, it can also complete the steering action, but the machine itself cannot realize the walking process. This is mainly due to the lack of oil and water caused by the damage of variable speed pump.

臂架不能起降，不能實現轉向動作，不能行走。這種情況多是由于攪拌斗傳動的鋼板連桿被螺栓剪斷和彈力板斷裂造成的。將柴油機和變速箱一起吊起，拆下變矩器柴油機的連接部位，檢查損壞部位，更換修理零件。

The boom cannot take off and land, cannot realize steering action, and cannot walk. This situation is mostly caused by the steel plate connecting rod driven by the mixing bucket being cut off by bolts and the elastic plate being broken. Lift the diesel engine and gearbox together, remove the connecting parts of the torque converter diesel engine, check the damaged parts, and replace and repair parts.

另外，要防止燃油漏入油底殼，因為油底殼會稀釋機油，使機油的粘度大大降低，過早失去潤滑作用。良好的霧化和合理的節氣門控制確保燃料的完全燃燒。

In addition, prevent the fuel from leaking into the oil pan, because the oil pan will dilute the oil, greatly reduce the viscosity of the oil and prematurely lose the lubricating effect. Good atomization and reasonable throttle control ensure the complete combustion of fuel.

避免發動機在高溫環境下工作，發動機一般要求正常工作溫度為80°C到95°C。如果溫度過高，油會變稀，還會加速油的變質。一旦發現溫度過高，要立即停機檢查，排除故障后才能繼續工作。

Avoid the engine working in high temperature environment. The normal working temperature of the engine is generally 80 ° C to 95 ° C. If the temperature is too high, the oil will become thin and accelerate the deterioration of the oil. Once the temperature is found to be too high, stop the machine immediately for inspection and continue to work after troubleshooting.

由于自動上料攪拌機長期使用會造成機械濾芯的堵塞，嚴重的堵塞會迫使閥打開，未經過濾的油液會在閥后直接進入動副表面被打開，這將加重機器。零件的磨損也會造成油底殼內雜質的堆積，加速油品的失效。因此，定期清洗過濾器和更換濾芯非常重要。

As the long-term use of the automatic feeding mixer will cause the blockage of the mechanical filter element, serious blockage will force the safety valve to open, and the unfiltered oil will directly enter the moving pair surface after the safety valve and be opened, which will aggravate the machine. The wear of parts will also cause the accumulation of impurities in the oil pan and accelerate the failure of oil products. Therefore, it is very important to clean the filter and replace the filter element regularly.

所以說，無論任何設備出現故障，都必須認真對待，找到問題的根源，然后找到相應的方案。更多內容就來網站www.wishnailspa.com進行咨詢吧。

Therefore, no matter any equipment fails, we must take it seriously, find the root cause of the problem, and then find the corresponding solution. For more information, please visit www.wishnailspa.com Com.