攪拌一體機在運用過程中，咱們要作業，要清楚了解拌和車在運用操作過程中應當留意哪些事項，下面小編為您解析需求留意的事項：

During the operation of the mixer, we should work safely, and clearly understand what should be paid attention to during the operation of the mixer. The following is a summary of what you need to pay attention to:

一、發動前應對機械系統各部位仔細進行查看，承認狀況正常后才能夠發動。

1、 Before starting, each part of the mechanical system shall be carefully checked, and it can only be started after it is acknowledged that the condition is normal.

二、發動前，拌和操縱桿有必要放在“空檔”方位。

2、 Before starting, it is necessary to place the mixing control lever in the "neutral" position.

三、發動后，應將拌和操縱桿放在“卸料”方位，放去筒內積水。

3、 After starting, place the mixing control lever at the "unloading" position to drain the accumulated water in the cylinder.

四、裝料時，拌和操作桿應當放在“裝料”方位。

4、 When loading, the mixing operating rod shall be placed in the "loading" position.

五、運送前，卸料槽有必要固定在“跋涉”方位，避免搖擺。

5、 Before transportation, it is necessary to fix the discharge chute at the "trek" position to avoid swinging.

六、操作操縱桿時，應在“空檔”方位稍作逗留后方可動下一個方位。

6、 When operating the control lever, stay in the "neutral" position for a while before moving to the next position.

七、咱們要做好文明施工，桶內多余材料不能隨意亂倒。卸料后有必要對拌和筒、料槽、托輥等部位進行清洗。

7、 We should do a good job in civilized construction. Excess materials in barrels should not be dumped randomly. After unloading, it is necessary to clean the mixing drum, material trough, idler and other parts.

八、人進入筒內鏟除砼結塊時，應將車輛熄火，拔下電門鑰匙，筒外應當有人進行監護。

8、 When people enter the cylinder to remove concrete caking, they should turn off the vehicle, pull out the switch key, and someone should be outside the cylinder for monitoring.

此外由于混凝土?xí)诙虝r(shí)間內凝結成硬塊，且對鋼材和油漆有一定的腐蝕性，所以每次運用混凝土貯罐后，洗凈粘附在混凝土貯罐及進出料口上的混凝土是每日維護有必要細心進行的工作。其間包括：

In addition, since the concrete will be condensed into hard blocks in a short time, and has a certain corrosivity to steel and paint, it is necessary to carefully clean the concrete adhered to the concrete storage tank and the inlet and outlet after each use of the concrete storage tank. This includes:

a．每次裝料前用水沖刷進料口，使進料口在裝料時堅持濕潤；

a. Before each loading, flush the feed inlet with water to keep it wet during loading;

b．在裝料的一同向隨車自帶的清洗用水水箱中注滿水；

b. Fill the water tank for cleaning water with the vehicle at the same time of loading;

c．裝料后沖刷進料口，洗凈進料口附近殘留的混凝土；

c. After loading, flush the feed inlet and clean the residual concrete near the feed inlet;

d．到工地卸料后，沖刷出料槽，然后向混凝土貯罐內加清洗用水30—40L；在車輛回程時堅持混凝土貯罐正向慢速滾動；

d. After unloading at the construction site, flush the discharge chute, and then add 30-40L of cleaning water to the concrete storage tank; Keep the concrete tank rolling slowly in the forward direction when the vehicle returns;

e．下次裝料前緊記放掉混凝土貯罐內的污水；

e. Remember to drain the sewage in the concrete storage tank before the next loading;

此外每天收工時清洗混凝土貯罐及進出料口周圍，保證不粘有水泥及混凝土結塊。以上這些工作只需一次不細心進行，就會給以后的工作帶來很大的費事。更多相關注意內容就來我們網站http://www.wishnailspa.com咨詢吧！

In addition, at the end of each day, the concrete storage tank and the area around the inlet and outlet shall be cleaned to ensure that there is no cement or concrete caking. If the above work is not carried out carefully once, it will bring great trouble to the future work. More relevant notes will come to our website http://www.wishnailspa.com Consult!