自動上料攪拌機出現“啃胎”怎么應對
來源：http://www.wishnailspa.com/日期：2022-09-30
概述：啃胎是指一個或多個輪胎的內側或外側出現異常加速磨損，與其他輪胎相比，一個輪胎的某一部分磨損得很快。怎么呢？接下來自動上料攪拌機
“啃胎”是指一個或多個輪胎的內側或外側出現異常加速磨損，與其他輪胎相比，一個輪胎的某一部分磨損得很快。怎么呢？接下來
自動上料攪拌機廠家簡單講一下。
"Tread" refers to abnormal accelerated wear on the inside or outside of one or more tires. Compared with other tires, a part of a tire wears quickly. How to solve it? Next, the manufacturer of automatic feeding mixer will give a brief introduction.
1，檢查全自動自動上料攪拌機氣壓是否過低或輪胎質量是否合格標準。
1. Check whether the air pressure of the automatic feeding mixer is too low or whether the tire quality is up to the standard.
2，檢查輪胎輪輞是否不圓，并做動平衡。
2. Check whether the tire rim is out of round and perform dynamic balancing.
3，檢查前束尺寸，轉向桿球頭是否松動，轉向器固定螺釘是否松動。
3. Check the toe in size, whether the steering rod ball head is loose, and whether the steering gear fixing screws are loose.
4，檢查轉向軸主軸或承壓—軸承是否磨損、嚴重變形或損壞。
4. Check whether the main shaft or pressure bearing of the steering shaft is worn, severely deformed or damaged.
5，后輪胎面不規則磨損。方法：檢查鋼圈、輪轂螺釘、軸頭螺釘是否松動。檢查制動轂是否不圓。檢查彈簧板和弓形夾固定螺釘是否松動。
5. The rear tire tread is worn irregularly. Solution: Check whether the steel ring, hub screw and shaft head screw are loose. Check whether the brake hub is out of round. Check whether the fixing screws of spring plate and bow clamp are loose.
6，增加輪胎充氣量可以減少輪胎與路面的接觸面積，從而降低輪胎的滾動阻力，節省燃油。但當充氣量過大時，會影響輪胎的減震性能，也會使輪胎變形過大，導致與地面接觸面積過小。這樣，磨損只能由胎面中部承擔，形成早期磨損。所以通貨膨脹的幅度應該是適當?shù)摹?/div>
6. Increasing the tire inflation can reduce the contact area between the tire and the road, thus reducing the rolling resistance of the tire and saving fuel. However, when the inflation volume is too large, the shock absorption performance of the tire will be affected, and the tire will also deform too much, resulting in too small contact area with the ground. In this way, the wear can only be borne by the middle of the tread, forming early wear. Therefore, the inflation rate should be appropriate.
The automatic feeding mixer may break down due to various reasons. What we need to do is to understand the problem in advance, then do a good job in prevention, and pay attention to us http://www.wishnailspa.com Learn more!
全國服務熱線
點擊撥打服務熱線：400-879-1999
