淺析如何處理上料攪拌機漏油現象！
來源：http://www.wishnailspa.com/日期：2020-08-07
概述： 作為自動上料攪拌機主人，掌握一些小的維修技巧是很有必要的，今天我們講一下攪拌機出現漏油現象怎么處理?！ s the owner of th
作為自動上料攪拌機主人，掌握一些小的維修技巧是很有必要的，今天我們講一下攪拌機出現漏油現象怎么處理。
As the owner of the automatic feeding mixer, it is necessary to master some small maintenance skills. Today, we will talk about how to deal with the oil leakage of the mixer.
1、冬季起車時預熱不足，油溫過低，油液和油封沒有達到工作溫度。
1. In winter, the preheating is insufficient, the oil temperature is too low, and the oil and oil seal do not reach the working temperature.
處理方案：起車時，停罐怠速運轉十到二十分鐘，待油溫正常后再轉罐工作。
Solution: when starting, stop the tank and idle for 10 to 20 minutes, and then turn the tank to work after the oil temperature is normal.
2、使用時間長，油封正常磨損。
2. It has been used for a long time and the oil seal is worn normally.
處理方案：更換新油封。
Treatment plan: replace the oil seal with a new one.
3、液壓油長期沒有更換或濾芯質量不合格，液壓油過臟，加速油封磨損。
3. The hydraulic oil has not been replaced for a long time or the quality of the filter element is unqualified, and the hydraulic oil is too dirty, which accelerates the wear of the oil seal.
處理方案：盡快更換液壓油和濾芯。
Treatment plan: replace hydraulic oil and filter element as soon as possible.
4、液壓油變質或乳化，潤滑性能下降，加速油封磨損。
4. The deterioration or emulsification of hydraulic oil leads to the decline of lubricating performance and the acceleration of oil seal wear.
處理方案：盡快更換液壓油和濾芯，嚴重時需要清洗系統。
Treatment plan: replace the hydraulic oil and filter element as soon as possible, and clean the system if it is serious.
5、傳動軸動平衡失效，擺動量大，引起主軸擺動油封偏磨。
5. The dynamic balance of the transmission shaft fails and the swing momentum is large, which causes eccentric wear of the oil seal of the spindle swing.
處理方案：及時校正或更換傳動軸。
Solution: correct or replace the transmission shaft in time.
6、泵支架松動、開焊或泵固定螺栓松動，引起液壓泵整體抖動，油封磨損。
6. Pump bracket loose, open welding or pump fixed bolt loose, causing the overall vibration of the hydraulic pump, oil seal wear.
處理方案：經常檢查，排除隱患，預防和避免故障。
Treatment plan: regular inspection, elimination of hidden dangers, prevention and avoidance of faults.
7、系統回油不暢，回油管或散熱器堵塞，造成泵馬達殼腔壓力增大，引起油封漏油。
7. The oil return of the system is not smooth, the oil return pipe or radiator is blocked, resulting in the increase of the pressure in the pump motor housing cavity, resulting in oil seal leakage.
處理方案：排除堵塞，保持回油循環順暢。
Treatment scheme: remove the blockage and keep the oil return circulation smooth.
8、散熱器不散熱，造成油溫過高，粘度和潤滑性下降、油封過熱密封失效。
8. The radiator does not dissipate heat, causing the oil temperature to be too high, the viscosity and the lubricity to drop, the oil seal overheats and seals to fail.
處理方案：及時排除散熱器故障，盡快為系統降溫，防止泵馬達磨損。必要時停自動上料攪拌機熄火，用水沖泵馬達和散熱器殼體降溫。
Treatment plan: timely remove the radiator failure, cooling the system as soon as possible to prevent pump motor wear. If necessary, stop the automatic feeding mixer, and wash the pump motor and radiator shell with water to cool down.
The above is about how to deal with the problem of oil leakage in automatic feeding mixer. I hope it can help you. If you want to know more, please click on our automatic charging mixer http://www.wishnailspa.com Official website.
全國服務熱線
點擊撥打服務熱線：400-879-1999
