我們作為一家自動上料攪拌機行業中的生產廠家，讓每個工作人員掌握維修技巧是非常重要的管理手段，今天我們針對漏油情況的發生，來講講對自動上料攪拌機本身所帶來的危害究竟有多大！并針對問題的出現給出相應的技巧。

As a professional manufacturer in the automatic feeding mixer industry, it is a very important management means to let each staff master the maintenance skills. Today, we are aiming at the occurrence of oil leakage to talk about the harm to the automatic feeding mixer itself! And for the emergence of the problem gives the corresponding solution skills.

在冬季起車時，若因預熱不足，油溫度就會出現過低。當油液、油封未達到工作溫度時，自動上料攪拌機在整個起車過程中，就需停罐怠速運轉10min20min，待油溫達到正常狀態后，再開始進行轉罐工作。

When starting in winter, the oil temperature will be too low due to insufficient preheating. When the oil and oil seal do not reach the working temperature, the automatic feeding mixer needs to stop the tank and idle for 10min to 20min during the whole starting process. After the oil temperature reaches the normal state, the tank can be rotated.

若使用時間過長，油封在達到正常磨損的情況下，就需對油封進行更換。

If the service time is too long, the oil seal needs to be replaced under the condition of normal wear.

液壓油缸時間未得到有效更換，或濾芯質量不合格，液壓油過臟，會加快油封磨損速度。盡快對自動上料攪拌機的液壓油及濾芯進行更換。

If the time of hydraulic cylinder is not effectively replaced, or the quality of filter element is unqualified, and the hydraulic oil is too dirty, the wear speed of oil seal will be accelerated. Replace the hydraulic oil and filter element of the automatic feeding mixer as soon as possible.
           

液壓油出現變質、乳化，潤滑性能下降，加快油封磨損速度，盡快更換液壓油、濾芯，嚴重時，還應對自動上料攪拌機的相關系統進行清洗。

The hydraulic oil deteriorates and emulsifies, the lubrication performance decreases, the oil seal wear speed is accelerated, and the hydraulic oil and filter element are replaced as soon as possible. When it is serious, the relevant systems of the automatic feeding mixer should be cleaned.

傳動軸動平衡失效，擺動量大，引起主軸擺動油封偏磨。及時對傳動軸進行校正或更換。

The dynamic balance failure of the transmission shaft and the large swing caused the eccentric wear of the main shaft swing oil seal. Correct or replace the transmission shaft in time.

系統回油不暢，回油管或散熱器發生堵塞，造成泵馬達殼腔壓力加大，引起油封漏油。排除堵塞情況，并保證回油循環達到順暢。

The oil return of the system is not smooth, and the oil return pipe or radiator is blocked, which increases the pressure of the pump motor housing cavity and causes oil leakage of the oil seal. Eliminate the blockage and ensure the smooth return oil circulation.

散熱器不散熱而造成油溫過高，粘度、潤滑性下降、油封過熱密封失效。及時排除散熱器故障，盡快為系統降溫，避免泵馬達出現磨損情況。必要時應讓自動上料攪拌機熄火，用水沖洗泵馬達、散熱器殼體，以達到降溫效果。

If the radiator does not dissipate heat, the oil temperature will be too high, the viscosity and lubricity will be reduced, the oil seal will overheat and the seal will fail. Remove the radiator fault in time, cool the system as soon as possible, and avoid the abrasion of the pump motor. If necessary, the automatic feeding mixer should be turned off, and the pump motor and radiator shell should be washed with water to achieve the cooling effect.