混凝土攪拌機設備已在行業中使用多年，由于其優越的便利性和穩定性，其市場占有率還是提高的。對于前期購買的客戶來說，由于設備的使用時間沒有增加，設備上的一些部件可能會老化，造成更多的機器問題。那么混凝土攪拌機出現這些故障可以做自檢！

　　Concrete mixer equipment has been used in the industry for many years, because of its superior convenience and stability, its market share is improved. For customers who purchased the equipment in the early stage, some parts of the equipment may age and cause more machine problems because the service time of the equipment has not increased. So the concrete mixer these failures can do self-inspection!

　　噪音大：這種情況可以分為兩種。攪拌時噪音大，可能是異物進入攪拌機造成的；機器空轉時噪音大。在這種情況下，需要檢查軸承中的潤滑油是否充足。一般是潤滑不足引起的軸承摩擦引起的。須添加對潤滑油的觀察。三是檢查攪拌器是否因與筒壁劇烈摩擦而變形。

　　Loud: There are two types of noise. Stirring noise, may be caused by foreign bodies into the blender; There is a lot of noise when the machine is idling. In this case, it is necessary to check whether the lubricating oil in the bearing is sufficient. It is generally caused by bearing friction caused by insufficient lubrication. Observations of lubricants must be added. Third, check whether the agitator is deformed by intense friction with the cylinder wall.

　　電機故障。如果電機不能運轉，一是檢查現場電壓是否低，二是電機接線是否使用兩相電。攪拌機一般使用三相電。如果用兩相電，電機不能運轉，功率不足。

　　Motor failure. If the motor cannot operate, one is to check whether the field voltage is low, and the other is whether the motor wiring is using two-phase electricity. Stone paint mixer generally uses three-phase electricity. If two - phase electricity is used, the motor will not operate and the power is insufficient.

　　設備軸承過熱。這個問題主要是潤滑油不足造成的，所以用戶要注意定期給設備加潤滑油。

　　Equipment bearing overheating. This problem is mainly caused by the lack of lubricating oil, so users should pay attention to regularly add lubricating oil to the equipment.

　　異常噪音。攪拌機如有異響，應及時停車，清理攪拌機內的雜物。

　　Abnormal noise. If there is any abnormal sound, stop the mixer in time and clean up the sundries in the mixer.

　　混凝土攪拌機的攪拌電機不工作。請檢查攪拌罐的鎖定裝置是否鎖定，限位開關是否復位。

　　The motor of the concrete mixer is not working. Please check whether the locking device of the mixing tank is locked and whether the limit switch is reset.

　　混凝土攪拌機抱軸問題?？赡苁窃贤读衔恢脝栴}。攪拌混凝土所用的物料主要是砂石骨料、水泥、粉煤灰、水和外加劑等。原料水泥若包裹砂石遇水結塊，如果攪拌不充分就容易粘在攪拌軸上，若水泥進料口位置方向不合理，使攪拌軸不能快速充分?jǐn)嚢?，就容易形成抱軸現象。

　　The concrete mixer holds the axle problem. It may be the feeding position of raw materials. Mixed concrete materials are mainly gravel aggregate, cement, fly ash, water and additives. If the raw cement is wrapped in sand and stone when it meets water, it is easy to stick to the mixing shaft if the mixing is not sufficient. If the direction of the cement feed port is unreasonable, the mixing shaft can not be fully stirred quickly, and it is easy to form the phenomenon of holding the shaft.

　　攪拌主機進水管與沖水位置原因。沖水點位置和沖洗方向不正確的話，又或者是沖水壓力過低，導致水在進入主機內部后，不能講暫時粘結在軸上的混凝土沖洗掉，則時間久了就容易形成抱軸。在結束生產之后沒有及時對攪拌機內部進行清洗，或清洗不干凈，導致攪拌軸表面仍有殘留的混凝土，干燥后凝固在攪拌軸上，如果長期如此則非常容易產生抱軸現象。

　　The reason for the inlet pipe and flushing position of the mixer. If the flushing point position and flushing direction are incorrect, or the flushing pressure is too low, resulting in water entering the main engine, the concrete temporarily bonded to the shaft can not be washed away, then it is easy to form the holding shaft over a long time. After the end of production, the internal of the mixer is not cleaned in time, or the cleaning is not clean, resulting in residual concrete on the surface of the mixing shaft, which will be solidified on the mixing shaft after drying. If this happens for a long time, the phenomenon of holding the shaft is very easy to occur.

　　混凝土攪拌機出現這些故障可以做自檢！以上便是問題的講解了，如果時間繼續累積和延長，故障率也會增加，所以一旦發現攪拌機不正常運行或者出現什么異樣情況，就請趕緊的停機做檢查工作。更多內容歡迎您來我們網站www.wishnailspa.com咨詢。

　　Concrete mixer occurrence these faults can do self - check! The above is the explanation of the problem. If the time continues to accumulate and prolong, the failure rate will increase. Therefore, once it is found that the blender does not run normally or something unusual happens, please stop the machine as soon as possible for inspection. You are welcome to visit our website www.wishnailspa.com for more information.