驅動系統是自動上料攪拌機和其他攪拌機很有價值的組件之一，所以在定期的檢查工作中也要去好好維護，不然一旦出現問題就會影響到攪拌機的使用效果以及工作效率，下面來了解下該組件吧。

　　The driving system is one of the most valuable components of the automatic feeding mixer and other mixers, so in the regular inspection work should also go to good maintenance, otherwise once there is a problem will affect the use effect and work efficiency of the mixer, the following to understand the component.

　　隨著工業的發展，設備有大型化的趨勢，自動上料攪拌機從設備底部安裝的也逐漸增多，底部安裝的攪拌機，攪拌軸短，不需設中間軸承和底軸承，軸所承受載荷小，運轉穩定，對密封也有利。為便于維修，底攪拌一般安裝在地面基礎上或是底部平臺上。

　　With the development of industry, there is a trend of large-scale equipment, automatic feeding mixer is gradually installed from the bottom of the equipment, the mixer installed at the bottom, the mixing shaft is short, there is no need to set intermediate bearings and bottom bearings, the shaft bears small load, stable operation, and is beneficial to sealing. In order to facilitate maintenance, the bottom agitation is generally installed on the ground foundation or the bottom platform.

　　自動上料攪拌機結構緊湊，傳動效率高，有些軸伸入較長的，還應設置內支撐架等。為方便帶料檢修，側攪拌一般都配備有專門的密封裝置，并帶有緊急切斷裝置。

　　Automatic feeding mixer is compact in structure, high transmission efficiency, some shafts extend into a longer, should also be set up in the support frame. In order to facilitate the maintenance of materials, side agitation is generally equipped with a special sealing device, and with an emergency cutting device.

　　自動上料攪拌機具有單獨的驅動裝置，一般包括電機、減速機、聯軸器等。攪拌機的動力源主要是各類電機、液壓馬達、氣動馬達等，實際應用多的是電機。當攪拌機的轉速很快，并和電機同步時，可與電機直接連用。

　　Automatic feeding mixer has a separate driving device, generally including motor, reducer, coupling and so on. The power source of blender is mainly all kinds of motor, hydraulic motor, pneumatic motor, etc., and the actual application is more motor. When the speed of the mixer is very fast and synchronized with the motor, it can be directly used with the motor.

　　聯軸器是連接電機、減速機與攪拌軸的重要部件，主要有剛性聯軸器和彈性聯軸器兩大類。驅動裝置的安裝方式有很多種，一般常用的是頂部安裝，根據減速機的安裝形式，有頂部立式安裝或頂部臥式安裝等，也有頂部傾斜安裝的。

　　Coupling is an important part of connecting motor, reducer and stirring shaft. It mainly includes rigid coupling and elastic coupling. There are many ways to install the drive device. The most commonly used is the top installation. According to the installation form of the reducer, there are vertical installation or horizontal installation at the top, and there are also inclined installation at the top.

　　保持減速器、皮帶或鏈條和鏈輪機構適當潤滑是要牢記的攪拌機維護技巧之一，定期檢查皮帶或鏈條的張緊度是重要的，皮帶或鏈條過松會打滑，可能會損壞鏈輪或燒毀皮帶。如果皮帶或鏈條太緊，它們將開始過早磨損軸承。將張力保持在制造商的建議范圍內，并每月檢查一次以確保它是正確的。

　　Keeping the reducer, belt or chain and sprocket mechanism properly lubricate is one of the blender maintenance tips to keep in mind. It is important to check the belt or chain tension regularly. Too loose a belt or chain can slip and damage the sprocket or burn the belt. If the belt or chain is too tight, they will begin to wear out the bearings prematurely. Keep the tension within the manufacturer's recommendations and check it once a month to make sure it is correct.

　　驅動裝置是自動上料攪拌機的重要組件的相關內容就講解的這里了，如果您對此感興趣或者有需求的話歡迎來我們網站www.wishnailspa.com咨詢，人員將竭誠為您服務。

　　The driving device is an important component of the automatic feeding mixer. The relevant content is explained here. If you are interested in this or have requirements, please come to our website www.wishnailspa.com for consultation, and professionals will serve you wholeheartedly.